Lun - Sab 9:00 am - 5:00 pm

Viper 2008-2010| ID1700-XDS

$3,045.00

ID1700-XDS, for Dodge SRT-10 / 8.3L & 8.4L engines. 14mm (clear) bottom adaptors. Set of 10.

Nominal Flow Rate – 1725cc/min @ 3.0 Bar (43.5 psi) Using Iso-Octane at 52 Degrees C (125 Degrees F)
Maximum Differential Fuel Pressure – 7.0 Bar (101.5 psi)
Fuel Compatibility – Compatible with Methanol/Ethanol/All Known Hydrocarbon Fuels.
Electrical Connector – USCAR

SKU: 1700.48.14.14B.10|Viper 2008-2010 Category: Tags: , , , ,

Description

The ID1700-XDS was designed to fill the gap between the ID1300-XDS and the ID2600-XDS, and like both, it features corrosion resistant internals making it compatible with all known automotive fuels.

A unique magnetic circuit, resulting from a lengthy development program, makes the ID1700-XDS immune to voltage and pressure sensitivity problems that plague other high impedance high flow injectors. The ID1700-XDS excels at high pressures typical of current automotive systems, and will perform flawlessly in these applications.

Application Notes

The ID1700-XDS was designed to be an all fuel compatible injector, capable of very high flow rates. As such, it will most often be used to deliver E85 to boosted engines, or occasionally, gasoline in extreme high horsepower applications. Neither of these applications requires extended linearity at low flow rates, and so this was given a proportionately lower priority during the design process.

The ID1700-XDS will deliver flawless stoichiometric idle and cruise mixtures on E85, but like the ID2600-XDS, should not be expected to do so on gasoline.

If you need flawless drivability on gasoline, the ID1300-XDS will provide this, and is capable of approximately 150hp per injector on E85.

Additional information

Weight 12 lbs
Dimensions 1 × 1 × 1 in
Brand

Injector Dynamics

Reviews

There are no reviews yet.

Be the first to review “Viper 2008-2010| ID1700-XDS”

Your email address will not be published. Required fields are marked *

Quick Comparison

SettingsViper 2008-2010| ID1700-XDS removeAlpha 70mm Throttle Body - B/D/F/H Series removeFuel Rail - Ultra Race - B Series Secondary removePro Intake Manifold - K20Z3 Style - Black removePro Intake Manifold - K20A2 Style - Black removeInlet Shield remove
NameViper 2008-2010| ID1700-XDS removeAlpha 70mm Throttle Body - B/D/F/H Series removeFuel Rail - Ultra Race - B Series Secondary removePro Intake Manifold - K20Z3 Style - Black removePro Intake Manifold - K20A2 Style - Black removeInlet Shield remove
ImageViper 2008-2010| ID1700-XDSViper 2008-2010| ID1700-XDSViper 2008-2010| ID1700-XDSViper 2008-2010| ID1700-XDSViper 2008-2010| ID1700-XDSViper 2008-2010| ID1700-XDS
SKU1700.48.14.14B.10|Viper 2008-2010309-05-1050350-05-6010307-05-0325307-05-03151000
Rating
Price$3,045.00 $125.99 $188.99 $504.99 $504.99$55.00$85.00
Stock
Availability
Add to cart

Select options

Add to cart

Add to cart

Add to cart

Add to cart

Select options

DescriptionID1700-XDS, for Dodge SRT-10 / 8.3L & 8.4L engines. 14mm (clear) bottom adaptors. Set of 10. Nominal Flow Rate – 1725cc/min @ 3.0 Bar (43.5 psi) Using Iso-Octane at 52 Degrees C (125 Degrees F) Maximum Differential Fuel Pressure – 7.0 Bar (101.5 psi) Fuel Compatibility – Compatible with Methanol/Ethanol/All Known Hydrocarbon Fuels. Electrical Connector – USCAR
309-05-1050
FEATURES: Precision Die-Cast Aluminum Fine Shot-Blasted Surface Finish Precision Machined Brass Throttle Plate Compatible w/ OEM Throttle Cable Sealed Ball Bearings for Smooth Operation New Throttle Body Gasket and Hardware Idle Adjustment Screws for Fine Tuning
350-05-6010 Engineers at Skunk2 Racing have developed a Secondary Fuel Rail for the popular Ultra Race Intake Manifold. FEATURES: Manufactured from Billet 6061 Aluminum Hard Anodized for Corrosion Resistance Large .669" Internal Bore -8 ORB Ports Supports Up to 1,200HP Compatible w/ E85 and Methanol. Requires Remote Mount Regulator.Ideal for turbocharged and naturally aspirated applications. 72mm throttle body opening can be port-matched up to 76mm. Only compatible with '06-'11 Civic Si K-series engine.307-05-0315 Ideal for turbocharged and naturally aspirated applications. 70mm throttle body opening can be port-matched up to 76mm. Not compatible with '06-'10 Civic Si K-series engine. *Re-uses OEM Coolant Neck*
  • 2003 - 2007 Honda Accord (2.4L EX/LX)
  • 2002 - 2005 Honda Civic (2.0L Si)
  • 2002 - 2005 Honda CR-V (2.4L EX/LX)
  • 2003 - 2011 Honda Element (2.4L EX/LX)
  • 2002 - 2006 Acura RSX (2.0L Base/Type S)

Inlet Shield is a product completely manufactured in Puerto Rico. It is designed to protect the turbo getting damage from any debris entering through the compressor wheel.

  • Using a Mesh in Stainless Steel 316, Custom Silicone Sleeve and a Tension Stainless Steel clamp
ContentThe ID1700-XDS was designed to fill the gap between the ID1300-XDS and the ID2600-XDS, and like both, it features corrosion resistant internals making it compatible with all known automotive fuels. A unique magnetic circuit, resulting from a lengthy development program, makes the ID1700-XDS immune to voltage and pressure sensitivity problems that plague other high impedance high flow injectors. The ID1700-XDS excels at high pressures typical of current automotive systems, and will perform flawlessly in these applications. Application Notes The ID1700-XDS was designed to be an all fuel compatible injector, capable of very high flow rates. As such, it will most often be used to deliver E85 to boosted engines, or occasionally, gasoline in extreme high horsepower applications. Neither of these applications requires extended linearity at low flow rates, and so this was given a proportionately lower priority during the design process. The ID1700-XDS will deliver flawless stoichiometric idle and cruise mixtures on E85, but like the ID2600-XDS, should not be expected to do so on gasoline. If you need flawless drivability on gasoline, the ID1300-XDS will provide this, and is capable of approximately 150hp per injector on E85.Skunk2 is proud to introduce the 70mm Alpha Series Throttle Body for Honda B16/ B17/ B18/ B20/ D15/ D16/ F20/ F22/ F23/ H22 and H23 engines in its exclusive, fine shot-blasted surface finish. Skunk2’s Alpha Series Throttle Body is designed to be used with Skunk2’s Pro Series Intake Manifolds as well as OEM and other aftermarket intake manifolds for bolt-on horsepower and torque gains by maximizing engine airflow, all at a competitive price.   A larger throttle body is key to producing additional power throughout the powerband on modified engines with increased airflow demands and the Skunk2’s 70mm Alpha Series Throttle Body delivers! Sealed ball bearings, a precision machined throttle plate and a honed oversized bore insures smooth operation on the most aggressive naturally aspirated and forced induction applications.
  • 1990 - 1997 Honda Accord (2.4L DX/LX/EX/SE)
  • 1992 - 2000 Honda Civic (1.6L DX/EX/GX/HX/LX/Si)
  • 1993 - 1997 Honda Del Sol (1.6L S/Si/VTEC)
  • 1992 - 2001 Honda Prelude (2.2L Base/Type SH)
  • 2000 - 2009 Honda S2000 (2.2L F22C)
  • 1990 - 2001 Acura Integra (1.8L GS/GS-R/LS/Type R)
NOTE: Due to Larger Diameter... You Must Use A Skunk2 Pro Series Intake Manifold or Make Adjustments to Intake Manifold Throttle Body Flange to Match Bore and Keep IAC (Idle Air Control) Passage Separate. Not compatible with B18C GS-R intake manifold. Not compatible with D Series engines featuring down-flow intake manifolds. Manual Transmission Only.
Fitment:
  • 1999 - 2000 Honda Civic (1.6L Si)
  • 1994 - 1997 Honda Del Sol (1.6L VTEC)
  • 1992 - 2001 Acura Integra (1.8L GS/GS-R/LS/Type R)
Skunk2's engineers went back to the drawing board when they set out to improve the already popular '06-'11 Civic Si’s RBC intake manifold. Each of Skunk2’s Pro Series Intake Manifolds for Honda’s K-series engines feature larger plenums and shorter, oversized runners when compared to the RBC, and are cast with thicker wall material, leaving room for further porting for high-horsepower applications. Instead of producing a manifold with a significantly oversized plenum and excessively short runners that would sacrifice mid-range power, Pro Series manifolds were designed for the “street enthusiast” who wants more power but doesn’t want to sacrifice mid-range performance to get it. The results are improved airflow, an enhanced venturi effect, and both mid-range and top-end power gains. Skunk2’s all-new, cast-aluminum Pro Series Intake Manifolds for Honda’s K-series engines are a direct-fit replacement for all '06-'11 Civic Si engines thanks to their unique design and throttle body flanges, which are compatible with OEM throttle bodies as well as those as large as 76mm. A thermal-insulated intake manifold gasket is also included, making for a truly bolt-on installation (no drilling or modifying required). Pro Series manifolds also incorporate an angled-runner design, which allows for ample hood clearance on almost any engine combination. Pro Series Intake Manifolds offer horsepower and torque gains greater than the popular RBC manifold but without compromising mid-range power output. The design incorporates runners that are similar in length to the RBC’s but with larger bores, a special tapered design, as well as a larger, tapered plenum that together preserve mid-range power but increase and accelerate airflow to allow for significant top-end power gains. Pro Series Intake Manifold runner exits are also machined and hand-finished to best match the cylinder head’s ports. Skunk2’s Pro Series Intake Manifold’s shape and design also increases wave scavenging effects at the engine’s ideal operating range, which allow for a broad increase in usable power. Skunk2 is a familiar name in the intake manifold business, with more than 10 years of experience designing, testing, and building them. Similar to OEM manifolds, Skunk2’s Pro Series Intake Manifolds are shell-molded from 356-aluminum, CNC-machined for superior strength, a precise fit, and a high-quality finish, and vacuum-tested for quality. Each manifold is molded with smooth transitions from the throttle body opening to the plenum to the runners with clean parting lines for an optimal finish, both inside and out and features a genuine Skunk2 nameplate.Skunk2's engineers looked to the popular '06-'10 Civic Si’s RBC intake manifold for inspiration when developing our Pro Series Intake Manifold for the '02-'05 Civic Si and '02-'06 RSX/ RSX Type S, and/ or any swap using the K20A/ K20A2/ K20Z1/ K24A1 engines or cylinder heads and we are happy to say they have finally arrived! Each of Skunk2’s Pro Series Intake Manifolds for Honda’s K-series engines feature larger plenums and shorter, oversized runners when compared to the RBC, and are cast with thicker wall material, leaving room for further porting for high-horsepower applications. Instead of producing a manifold with a significantly oversized plenum and excessively short runners that would sacrifice mid-range power, Pro Series manifolds were designed for the “street enthusiast” who wants more power but doesn’t want to sacrifice mid-range performance to get it. The results are improved airflow, an enhanced venturi effect, and both mid-range and top-end power gains. Skunk2’s all-new, cast-aluminum Pro Series Intake Manifolds for Honda’s K-series engines are a direct-fit replacement for all K-series engines (excluding '06-'10 Civic Si) thanks to their unique, patent-pending throttle body flanges, which are compatible with OEM throttle bodies as well as those as large as 76mm. Pro Series manifolds also incorporate an angled-runner design, which allows for ample hood clearance on ’88-’00 Civics and ’90-’01 Integras with K-series engine swaps, as well as additional core support clearance on ’02-’05 Civic Si. Pro Series Intake Manifolds offer horsepower and torque gains greater than the popular RBC manifold but without compromising mid-range power output. The design incorporates runners that are similar in length to the RBC’s but with larger bores, a special tapered design, as well as a larger, tapered plenum that together preserve mid-range power but increase and accelerate airflow to allow for significant top-end power gains. Pro Series Intake Manifold runner exits are also machined and hand-finished to best match the cylinder head’s ports. Skunk2’s Pro Series Intake Manifold’s shape and design also increases wave scavenging effects at the engine’s ideal operating range, which allow for a broad increase in usable power. Skunk2 is a familiar name in the intake manifold business, with more than 10 years of experience designing, testing, and building them. Similar to OEM manifolds, Skunk2’s Pro Series Intake Manifolds are shell-molded from 356-aluminum, CNC-machined for superior strength, a precise fit, and a high-quality finish, and vacuum-tested for quality. Each manifold is molded with smooth transitions from the throttle body opening to the plenum to the runners with clean parting lines for an optimal finish, both inside and out and features a genuine Skunk2 nameplate.
Weight12 lbs1.9 lbs1.25 lbsN/AN/A1 lbs
Dimensions1 × 1 × 1 in10 × 8 × 8 in16 × 5 × 3 inN/AN/A7 × 8 × 1 in
Additional information
Weight 12 lbs
Dimensions 1 × 1 × 1 in
Brand

Injector Dynamics

Weight 1.9 lbs
Dimensions 10 × 8 × 8 in
Brand

Skunk2

Weight 1.25 lbs
Dimensions 16 × 5 × 3 in
Brand

Skunk2

Brand

Skunk2

Brand

Skunk2

Weight 1 lbs
Dimensions 7 × 8 × 1 in
Brand

Inlet Shield

Select the fields to be shown. Others will be hidden. Drag and drop to rearrange the order.
  • Image
  • SKU
  • Rating
  • Price
  • Stock
  • Availability
  • Add to cart
  • Description
  • Content
  • Weight
  • Dimensions
  • Additional information
  • Attributes
  • Custom attributes
  • Custom fields
Click outside to hide the comparison bar
Compare
X