Lun - Sab 9:00 am - 5:00 pm

HomeShopFuel SystemInjectorsID1700-XDSFordMustang GT 88-96| ID1700-XDS

Mustang GT 88-96| ID1700-XDS

$2,436.00$2,494.80

ID1700-XDS, for Mustang GT 5.0L applications. 14mm (purple) adapters. Set of 8.

Nominal Flow Rate – 1725cc/min @ 3.0 Bar (43.5 psi) Using Iso-Octane at 52 Degrees C (125 Degrees F)
Maximum Differential Fuel Pressure – 7.0 Bar (101.5 psi)
Fuel Compatibility – Compatible with Methanol/Ethanol/All Known Hydrocarbon Fuels.
Electrical Connector – USCAR

SKU: 1700.60.14.14.8|Mustang GT 88-96 Category: Tags: , , , ,

Description

The ID1700-XDS was designed to fill the gap between the ID1300-XDS and the ID2600-XDS, and like both, it features corrosion resistant internals making it compatible with all known automotive fuels.

A unique magnetic circuit, resulting from a lengthy development program, makes the ID1700-XDS immune to voltage and pressure sensitivity problems that plague other high impedance high flow injectors. The ID1700-XDS excels at high pressures typical of current automotive systems, and will perform flawlessly in these applications.

Application Notes

The ID1700-XDS was designed to be an all fuel compatible injector, capable of very high flow rates. As such, it will most often be used to deliver E85 to boosted engines, or occasionally, gasoline in extreme high horsepower applications. Neither of these applications requires extended linearity at low flow rates, and so this was given a proportionately lower priority during the design process.

The ID1700-XDS will deliver flawless stoichiometric idle and cruise mixtures on E85, but like the ID2600-XDS, should not be expected to do so on gasoline.

If you need flawless drivability on gasoline, the ID1300-XDS will provide this, and is capable of approximately 150hp per injector on E85.

Additional information

Weight 12 lbs
Dimensions 1 × 1 × 1 in
Brand

Injector Dynamics

Reviews

There are no reviews yet.

Be the first to review “Mustang GT 88-96| ID1700-XDS”

Your email address will not be published. Required fields are marked *

Quick Comparison

SettingsMustang GT 88-96| ID1700-XDS removeHigh Volume Fuel Rail Mitsubishi EVO VIII IX removeFuel Rail - Ultra Race - B Series Primary removeAlpha 70mm Throttle Body - B/D/F/H Series removePro Intake Manifold - D Series removeUltra Race Plenum Spacer - 1L Black remove
NameMustang GT 88-96| ID1700-XDS removeHigh Volume Fuel Rail Mitsubishi EVO VIII IX removeFuel Rail - Ultra Race - B Series Primary removeAlpha 70mm Throttle Body - B/D/F/H Series removePro Intake Manifold - D Series removeUltra Race Plenum Spacer - 1L Black remove
ImageMustang GT 88-96| ID1700-XDSMustang GT 88-96| ID1700-XDSMustang GT 88-96| ID1700-XDSMustang GT 88-96| ID1700-XDSMustang GT 88-96| ID1700-XDSMustang GT 88-96| ID1700-XDS
SKU1700.60.14.14.8|Mustang GT 88-96350-06-5100350-05-6000309-05-1050307-05-0260907-05-9051
Rating
Price$2,436.00$2,494.80 $210.99 $188.99 $125.99 $252.99 $141.99
Stock
Availability
Add to cart

Select options

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

DescriptionID1700-XDS, for Mustang GT 5.0L applications. 14mm (purple) adapters. Set of 8. Nominal Flow Rate – 1725cc/min @ 3.0 Bar (43.5 psi) Using Iso-Octane at 52 Degrees C (125 Degrees F) Maximum Differential Fuel Pressure – 7.0 Bar (101.5 psi) Fuel Compatibility – Compatible with Methanol/Ethanol/All Known Hydrocarbon Fuels. Electrical Connector – USCAR350-06-5100 Fitment:
  • 2003 - 2005 Mitsubishi Lancer Evolution VIII (2.0L Turbo)
  • 2006 - 2007 Mitsubishi Lancer Evolution IX (2.0L Turbo)
Features: · Up to 3% Gain Just by Keeping Fuel Cooler · -8 AN End Threads with 0.625" Internal Bore · Can Support Up to 1200HP · Can Be Used with Stock Fuel System · Chemical Resistant to All Fuels including Alcohol  
350-05-6000 Engineers at Skunk2 Racing have developed a Primary Fuel Rail for the popular Ultra Race Intake Manifold. FEATURES: Manufactured from Billet 6061 Aluminum Hard Anodized for Corrosion Resistance Large .669" Internal Bore -8 ORB Ports Supports Up to 1,200HP Compatible w/ E85 and Methanol. Requires Remote Mount Regulator.
309-05-1050
FEATURES: Precision Die-Cast Aluminum Fine Shot-Blasted Surface Finish Precision Machined Brass Throttle Plate Compatible w/ OEM Throttle Cable Sealed Ball Bearings for Smooth Operation New Throttle Body Gasket and Hardware Idle Adjustment Screws for Fine Tuning
307-05-0260 Not compatible with OEM D-series throttle body. Must use larger-bore Skunk2 throttle body or similar. Not directly compatible with Civic Wagon or Wagovan; clearance modifications required. Not directly compatible with '96-'00 Civic; brake proportioning valve and fuel filter clearance required. Ideal for turbocharged and naturally aspirated applications. 66mm throttle body opening can be port-matched up to 70mm.907-05-9051 The Skunk2 Racing Plenum Spacer is used to increase the internal volume of the Ultra "Race" Intake Manifolds by 1 Liter. INCLUDES: Billet Aluminum Spacer Longer Socket Head Hardware Gaskets
ContentThe ID1700-XDS was designed to fill the gap between the ID1300-XDS and the ID2600-XDS, and like both, it features corrosion resistant internals making it compatible with all known automotive fuels. A unique magnetic circuit, resulting from a lengthy development program, makes the ID1700-XDS immune to voltage and pressure sensitivity problems that plague other high impedance high flow injectors. The ID1700-XDS excels at high pressures typical of current automotive systems, and will perform flawlessly in these applications. Application Notes The ID1700-XDS was designed to be an all fuel compatible injector, capable of very high flow rates. As such, it will most often be used to deliver E85 to boosted engines, or occasionally, gasoline in extreme high horsepower applications. Neither of these applications requires extended linearity at low flow rates, and so this was given a proportionately lower priority during the design process. The ID1700-XDS will deliver flawless stoichiometric idle and cruise mixtures on E85, but like the ID2600-XDS, should not be expected to do so on gasoline. If you need flawless drivability on gasoline, the ID1300-XDS will provide this, and is capable of approximately 150hp per injector on E85.Skunk2’s Composite Fuel Rails are made using a proprietary casting process, from a carbon reinforced aerospace thermo-polymer composite that is 33% lighter, 60% stronger, and runs up to 100 degrees (F) cooler than aluminum. The Composite Fuel Rail insulates fuel from both radiant and conductive heat transfer underneath the hood better than aluminum, resulting in increased horsepower and torque.   Composite Fuel Rails also feature large 0.625-inch internal bores for superior fuel injector pulsation dampening, machined with a smooth interior finish and feature radius-cut fuel injector outlets for improved flow characteristics. Conventional extruded and drilled aluminum rails are typically flawed by design due to machine limitations, resulting sharp internal angles where the main bore meets the fuel injector bores. Eliminating this design flaw limitation can only be achieved with the natural-flow-moldable composite materials. Skunk2’s Composite Fuel Rails are compatible with the factory fuel system, as well as all pump and race fuels, including alcohol. The Skunk2 Composite Fuel Rail can support up to 1,200hp, with gains as high as three percent realized during testing.    Fitment:
  • 1999 - 2000 Honda Civic (1.6L Si)
  • 1994 - 1997 Honda Del Sol (1.6L VTEC)
  • 1992 - 2001 Acura Integra (1.8L GS/GS-R/LS/Type R)
Skunk2 is proud to introduce the 70mm Alpha Series Throttle Body for Honda B16/ B17/ B18/ B20/ D15/ D16/ F20/ F22/ F23/ H22 and H23 engines in its exclusive, fine shot-blasted surface finish. Skunk2’s Alpha Series Throttle Body is designed to be used with Skunk2’s Pro Series Intake Manifolds as well as OEM and other aftermarket intake manifolds for bolt-on horsepower and torque gains by maximizing engine airflow, all at a competitive price.   A larger throttle body is key to producing additional power throughout the powerband on modified engines with increased airflow demands and the Skunk2’s 70mm Alpha Series Throttle Body delivers! Sealed ball bearings, a precision machined throttle plate and a honed oversized bore insures smooth operation on the most aggressive naturally aspirated and forced induction applications.
  • 1990 - 1997 Honda Accord (2.4L DX/LX/EX/SE)
  • 1992 - 2000 Honda Civic (1.6L DX/EX/GX/HX/LX/Si)
  • 1993 - 1997 Honda Del Sol (1.6L S/Si/VTEC)
  • 1992 - 2001 Honda Prelude (2.2L Base/Type SH)
  • 2000 - 2009 Honda S2000 (2.2L F22C)
  • 1990 - 2001 Acura Integra (1.8L GS/GS-R/LS/Type R)
NOTE: Due to Larger Diameter... You Must Use A Skunk2 Pro Series Intake Manifold or Make Adjustments to Intake Manifold Throttle Body Flange to Match Bore and Keep IAC (Idle Air Control) Passage Separate. Not compatible with B18C GS-R intake manifold. Not compatible with D Series engines featuring down-flow intake manifolds. Manual Transmission Only.
More than a decade ago, Skunk2's engineers revolutionized Honda performance by creating the first-ever, high-flow, cast aluminum intake manifold. Skunk2’s Pro Series Intake Manifold for most Honda SOHC D-series engines features a larger plenum and oversized runners when compared to the OEM version for maximum horsepower and torque gains. Instead of producing a manifold with a significantly oversized plenum and excessively short runners that would sacrifice mid-range power, the Pro Series manifold was designed for the “street enthusiast” who wants more power but doesn’t want to sacrifice mid-range performance to get it. The results are improved airflow, an enhanced venturi effect, and both mid-range and top-end power gains. Skunk2’s cast-aluminum Pro Series Intake Manifolds for Honda’s D-series engines are a direct-fit replacement for most D-series engines and are compatible with all factory sensors. Pro Series Intake Manifolds offer horsepower and torque gains greater than competitors’ manifolds but without compromising mid-range power output. The design incorporates specially tapered runners as well as a larger, tapered plenum that together preserve mid-range power but increase and accelerate airflow to allow for significant top-end power gains. Pro Series Intake Manifold runner exits are also machined to best match the cylinder head’s ports. Skunk2’s Pro Series Intake Manifold’s shape and design also increases wave scavenging effects at the engine’s ideal operating range, which allow for a broad increase in usable power. Skunk2 is a familiar name in the intake manifold business, with more than 10 years of experience designing, testing, and building them. Similar to OEM manifolds, Skunk2’s Pro Series Intake Manifolds are shell-molded from 356-aluminum, CNC-machined for superior strength, a precise fit, and a high-quality finish, and vacuum-tested for quality. Each manifold is molded with smooth transitions from the throttle body opening to the plenum to the runners with clean parting lines for an optimal finish, both inside and out and features a genuine Skunk2 nameplate.
Weight12 lbs2 lbs1.25 lbs1.9 lbsN/A3 lbs
Dimensions1 × 1 × 1 in18 × 6 × 6 in16 × 5 × 3 in10 × 8 × 8 inN/A20 × 8 × 8 in
Additional information
Weight 12 lbs
Dimensions 1 × 1 × 1 in
Brand

Injector Dynamics

Weight 2 lbs
Dimensions 18 × 6 × 6 in
Brand

Skunk2

Weight 1.25 lbs
Dimensions 16 × 5 × 3 in
Brand

Skunk2

Weight 1.9 lbs
Dimensions 10 × 8 × 8 in
Brand

Skunk2

Brand

Skunk2

Weight 3 lbs
Dimensions 20 × 8 × 8 in
Brand

Skunk2

Select the fields to be shown. Others will be hidden. Drag and drop to rearrange the order.
  • Image
  • SKU
  • Rating
  • Price
  • Stock
  • Availability
  • Add to cart
  • Description
  • Content
  • Weight
  • Dimensions
  • Additional information
  • Attributes
  • Custom attributes
  • Custom fields
Click outside to hide the comparison bar
Compare
X