Lun - Sab 9:00 am - 5:00 pm

HomeShopFuel SystemInjectorsID1700-XDSFordFG Falcon GT and GS 5.0 – 10-16| ID1700-XDS

FG Falcon GT and GS 5.0 – 10-16| ID1700-XDS

ID1700-XDS, for Ford FG Falcon GT and GS, 5 liter, 2010-2016. 14 mm (grey) adaptor top AND (silver) BOTTOM adaptor. Potted 4″ leads with USCAR male connectors. Set of 8.

Nominal Flow Rate – 1725cc/min @ 3.0 Bar (43.5 psi) Using Iso-Octane at 52 Degrees C (125 Degrees F)
Maximum Differential Fuel Pressure – 7.0 Bar (101.5 psi)
Fuel Compatibility – Compatible with Methanol/Ethanol/All Known Hydrocarbon Fuels.
Electrical Connector – USCAR

This product is currently out of stock and unavailable.

SKU: 1700.60.14.14B.8-PU|FG Falcon GT and GS 5.0 - 10-16 Category: Tags: , , , ,

Description

The ID1700-XDS was designed to fill the gap between the ID1300-XDS and the ID2600-XDS, and like both, it features corrosion resistant internals making it compatible with all known automotive fuels.

A unique magnetic circuit, resulting from a lengthy development program, makes the ID1700-XDS immune to voltage and pressure sensitivity problems that plague other high impedance high flow injectors. The ID1700-XDS excels at high pressures typical of current automotive systems, and will perform flawlessly in these applications.

Application Notes

The ID1700-XDS was designed to be an all fuel compatible injector, capable of very high flow rates. As such, it will most often be used to deliver E85 to boosted engines, or occasionally, gasoline in extreme high horsepower applications. Neither of these applications requires extended linearity at low flow rates, and so this was given a proportionately lower priority during the design process.

The ID1700-XDS will deliver flawless stoichiometric idle and cruise mixtures on E85, but like the ID2600-XDS, should not be expected to do so on gasoline.

If you need flawless drivability on gasoline, the ID1300-XDS will provide this, and is capable of approximately 150hp per injector on E85.

Additional information

Weight 12 lbs
Dimensions 1 × 1 × 1 in
Brand

Injector Dynamics

Reviews

There are no reviews yet.

Be the first to review “FG Falcon GT and GS 5.0 – 10-16| ID1700-XDS”

Your email address will not be published. Required fields are marked *

Quick Comparison

SettingsFG Falcon GT and GS 5.0 - 10-16| ID1700-XDS removeUltra Street Intake Manifold - B VTEC - Black removeHigh Volume Fuel Rail Mitsubishi EVO VIII IX removePro Intake Manifold - EVO VIII-IX - Black removePro Intake Manifold - EVO VIII-IX removeSkunk2 Ultra Street Intake Manifold - K20A2 Style - Black remove
ImageFG Falcon GT and GS 5.0 – 10-16| ID1700-XDSFG Falcon GT and GS 5.0 – 10-16| ID1700-XDSFG Falcon GT and GS 5.0 – 10-16| ID1700-XDSFG Falcon GT and GS 5.0 – 10-16| ID1700-XDSFG Falcon GT and GS 5.0 – 10-16| ID1700-XDSFG Falcon GT and GS 5.0 – 10-16| ID1700-XDS
SKU1700.60.14.14B.8-PU|FG Falcon GT and GS 5.0 - 10-16307-05-0505350-06-5100307-06-0505307-06-0500307-05-0605
Rating
Price $462.99 $210.99 $504.99 $483.99 $578.99
Stock

Out of stock

AvailabilityOut of stock
Add to cart

Read more

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

DescriptionID1700-XDS, for Ford FG Falcon GT and GS, 5 liter, 2010-2016. 14 mm (grey) adaptor top AND (silver) BOTTOM adaptor. Potted 4" leads with USCAR male connectors. Set of 8. Nominal Flow Rate – 1725cc/min @ 3.0 Bar (43.5 psi) Using Iso-Octane at 52 Degrees C (125 Degrees F) Maximum Differential Fuel Pressure – 7.0 Bar (101.5 psi) Fuel Compatibility – Compatible with Methanol/Ethanol/All Known Hydrocarbon Fuels. Electrical Connector – USCAR307-05-0505 FEATURES: Modular 2pc. Design w/ Removable Plenum Rotatable Plenum Allows Driver-side or Passenger-Side Throttle Body Mounting 1.8L Plenum Volume
** Tapered 8.72" Long High-Velocity Runners w/ Raised Velocity Stack Entries Generously Cast Runner Walls for Porting
 74mm Throttle Body Opening Lightweight 356 Aluminum Alloy Construction 2 x 1/8" NPT and 2 x 1/4" NPT Accessory Ports Hi-Grade Mounting Hardware Thermal Gasket Included Fitment:
  • 1999 - 2000 Honda Civic (1.6L Si)
  • 1994 - 1995 Honda Del Sol (1.6L VTEC)
  • 1992 - 2001 Acura Integra (1.8L GS-R/Type R)
Will NOT work with factory throttle body A minimum of a 68mm throttle body is required.   **Optional Billet Aluminum Plenum Spacer Available in .5L Size  
350-06-5100 Fitment:
  • 2003 - 2005 Mitsubishi Lancer Evolution VIII (2.0L Turbo)
  • 2006 - 2007 Mitsubishi Lancer Evolution IX (2.0L Turbo)
Features: · Up to 3% Gain Just by Keeping Fuel Cooler · -8 AN End Threads with 0.625" Internal Bore · Can Support Up to 1200HP · Can Be Used with Stock Fuel System · Chemical Resistant to All Fuels including Alcohol  
307-06-0505 Match with a Skunk2 Pro Series Throttle Body for an easy 30+ hp gain. -NPT threaded ports - Hardware with plugs or barbed fittings for vacuum purposes - Dipstick Relocator307-06-0500 Match with a Skunk2 Pro Series Throttle Body for an easy 30+ hp gain. -NPT threaded ports - Hardware with plugs or barbed fittings for vacuum purposes - Dipstick Relocator  
  • 2003 - 2005 Mitsubishi Lancer Evolution VIII (2.0L Turbo)
  • 2006 - 2007 Mitsubishi Lancer Evolution IX (2.0L Turbo)
  • 1994 - 1998 Mitsubishi Eclipse (2.0L 4G63T GST/GSX)
307-05-0605 FEATURES: Modular 2pc. Design w/ Removable Plenum Rotatable Plenum Allows Driver-side or Passenger-Side Throttle Body Mounting 1.8L Plenum Volume
** Tapered 6.85" Long High-Velocity Runners w/ Raised Velocity Stack Entries Generously Cast Runner Walls for Porting 71mm Throttle Body Opening Lightweight 356 Aluminum Alloy Construction Hi-Grade Mounting Hardware Thermal Gasket Included 2 x 1/4" NPT and 2 x 1/8" NPT Accessory Ports   **Optional Billet Aluminum Plenum Spacer Available in .5L Size  
ContentThe ID1700-XDS was designed to fill the gap between the ID1300-XDS and the ID2600-XDS, and like both, it features corrosion resistant internals making it compatible with all known automotive fuels. A unique magnetic circuit, resulting from a lengthy development program, makes the ID1700-XDS immune to voltage and pressure sensitivity problems that plague other high impedance high flow injectors. The ID1700-XDS excels at high pressures typical of current automotive systems, and will perform flawlessly in these applications. Application Notes The ID1700-XDS was designed to be an all fuel compatible injector, capable of very high flow rates. As such, it will most often be used to deliver E85 to boosted engines, or occasionally, gasoline in extreme high horsepower applications. Neither of these applications requires extended linearity at low flow rates, and so this was given a proportionately lower priority during the design process. The ID1700-XDS will deliver flawless stoichiometric idle and cruise mixtures on E85, but like the ID2600-XDS, should not be expected to do so on gasoline. If you need flawless drivability on gasoline, the ID1300-XDS will provide this, and is capable of approximately 150hp per injector on E85.The much anticipated Ultra "Street" intake manifolds for the Honda B16A/ B17A and B18C engine or VTEC cylinder heads has finally arrived! The Ultra Series is years of research and development, culminated in a multi-piece cast aluminum intake manifold that offers advantages that only a modular design could allow. Using the latest in CFD (Computational Fluid Dynamics) software; Skunk2 Racing has created a two-piece modular design that allows for easy disassembly, porting, and plenum volume changes through the use of a removable plenum lid and optional plenum spacers. In addition to CFD testing, the Ultra Series Intake Manifold has undergone extensive in-house dyno testing which has led to a design that is less restrictive, yielding both torque and power gains well over many of the competitors. Skunk2 Racing Ultra Street Intake Manifolds are cast-aluminum, manufactured from high-grade 356 aluminum alloy for strength and lightweight. Each manifold is CNC-machined for a precise fit, and individually inspected for quality assurance. The Ultra Series Street manifold features a generous 74mm throttle body opening and is constructed with thick walls at entry, minimizing concerns of breakthrough when port matching. Intense planning and design went into the plenum to distribute even airflow to all four cylinders under dynamic load conditions. Placement and design of the velocity stacks were rigorously flow tested to ensure maximum delivery of air to the cylinder. Large velocity stack raised bell mouth entries lead to 8.72” long intake runners with smooth transitions allowing the Ultra Street Intake Manifold to really move some air! Skunk2 Racing Ultra Street Intake Manifolds are designed to be used in modified naturally aspirated applications as well as mild turbo/supercharged setups.Skunk2’s Composite Fuel Rails are made using a proprietary casting process, from a carbon reinforced aerospace thermo-polymer composite that is 33% lighter, 60% stronger, and runs up to 100 degrees (F) cooler than aluminum. The Composite Fuel Rail insulates fuel from both radiant and conductive heat transfer underneath the hood better than aluminum, resulting in increased horsepower and torque.   Composite Fuel Rails also feature large 0.625-inch internal bores for superior fuel injector pulsation dampening, machined with a smooth interior finish and feature radius-cut fuel injector outlets for improved flow characteristics. Conventional extruded and drilled aluminum rails are typically flawed by design due to machine limitations, resulting sharp internal angles where the main bore meets the fuel injector bores. Eliminating this design flaw limitation can only be achieved with the natural-flow-moldable composite materials. Skunk2’s Composite Fuel Rails are compatible with the factory fuel system, as well as all pump and race fuels, including alcohol. The Skunk2 Composite Fuel Rail can support up to 1,200hp, with gains as high as three percent realized during testing.    The intake manifold solution street-driven Evo VIII-IX owners have been waiting for is here. Skunk2’s Evo Pro Series Intake Manifold in its signature Black Series finish was designed with “street enthusiasts” who utilize turbochargers as small as the factory unit in mind and want more power without sacrificing mid-range performance. Skunk2’s all-new, cast-aluminum Evo Pro Series Intake Manifold—which was tested and developed on the company’s own Evo Time Attack race car—is a direct-fit replacement and offers significant horsepower and torque gains without compromising mid-range power output. Conventional large-plenum, short-runner intake manifolds provide top-end power gains but suffer in the mid-range. Not Skunk2’s. Its all-new Pro Series Intake Manifold features OEM-length runners with larger bores and a special tapered design as well as a larger, tapered plenum that together preserve mid-range power but increase and accelerate airflow to allow for significant top-end gains. Peak gains as high as 33+ whp have been realized when paired with Pro Series Throttle Bodies with positive results across the board, beginning as low as 3,200 rpm. Pro Series Intake Manifolds also feature thicker castings when compared to the OEM piece, which leaves plenty of room for porting, and each runner exit is machined and hand-finished to best match the cylinder head’s ports. The Pro Series Intake Manifold’s unique design increases wave scavenging effects at the engine’s ideal operating range, which allow for a broad increase in usable power. Skunk2’s Evo Pro Series Intake Manifold is a simple bolt-on affair. Unlike other intake manifolds, Skunk2’s incorporates the factory configuration, leaving the throttle body in its original location, which means the original intercooler piping and hoses can be reused. Pro Series Intake Manifolds also include the necessary provisions for the Evo’s brake booster line, MDP sensor, and vacuum accessories (EGR valve excluded), and incorporate two additional 1/8-inch NPT threaded ports, which can be used for any number of vacuum/boost-related devices such as gauges, boost controllers, and more.Each manifold comes equipped with plugs and fittings as well as a dipstick k relocator. Skunk2 is a familiar name in the intake manifold business, with more than 10 years of experience designing, testing, and building them. Similar to OEM manifolds, Skunk2’s Pro Series Intake Manifolds are shell-molded from 356-aluminum, CNC-machined for superior strength, a precise fit, and a high-quality finish, and vacuum-tested for quality. Each manifold is molded with smooth transitions from the throttle body opening to the plenum to the runners with clean parting lines for an optimal finish, both inside and out and features a genuine Skunk2 nameplate.The intake manifold solution street-driven Evo VIII-IX owners have been waiting for is here. Skunk2’s newly designed Evo Pro Series Intake Manifold was designed with “street enthusiasts” who utilize turbochargers as small as the factory unit in mind and want more power without sacrificing mid-range performance. Skunk2’s all-new, cast-aluminum Evo Pro Series Intake Manifold—which was tested and developed on the company’s own Evo Time Attack race car—is a direct-fit replacement and offers significant horsepower and torque gains without compromising mid-range power output. Conventional large-plenum, short-runner intake manifolds provide top-end power gains but suffer in the mid-range. Not Skunk2’s. Its all-new Pro Series Intake Manifold features OEM-length runners with larger bores and a special tapered design as well as a larger, tapered plenum that together preserve mid-range power but increase and accelerate airflow to allow for significant top-end gains. Peak gains as high as 33+ whp have been realized when paired with Pro Series Throttle Bodies with positive results across the board, beginning as low as 3,200 rpm. Pro Series Intake Manifolds also feature thicker castings when compared to the OEM piece, which leaves plenty of room for porting, and each runner exit is machined and hand-finished to best match the cylinder head’s ports. The Pro Series Intake Manifold’s unique design increases wave scavenging effects at the engine’s ideal operating range, which allow for a broad increase in usable power. Skunk2’s Evo Pro Series Intake Manifold is a simple bolt-on affair. Unlike other intake manifolds, Skunk2’s incorporates the factory configuration, leaving the throttle body in its original location, which means the original intercooler piping and hoses can be reused. Pro Series Intake Manifolds also include the necessary provisions for the Evo’s brake booster line, MDP sensor, and vacuum accessories (EGR valve excluded), and incorporate two additional 1/8-inch NPT threaded ports, which can be used for any number of vacuum/boost-related devices such as gauges, boost controllers, and more. Each manifold comes equipped with plugs and fittings as well as a dipstick k relocator. Skunk2 is a familiar name in the intake manifold business, with more than 10 years of experience designing, testing, and building them. Similar to OEM manifolds, Skunk2’s Pro Series Intake Manifolds are shell-molded from 356-aluminum, CNC-machined for superior strength, a precise fit, and a high-quality finish, and vacuum-tested for quality. Each manifold is molded with smooth transitions from the throttle body opening to the plenum to the runners with clean parting lines for an optimal finish, both inside and out and features a genuine Skunk2 nameplate.The much anticipated Ultra "Street" Intake Manifold for the '02-'05 Civic Si and '02-'06 RSX/ RSX Type S, and/ or any swap using the K20A/ K20A2/ K20Z1/ K24A1 engines or cylinder heads has finally arrived!   The Ultra Series is years of research and development, culminated in a multi-piece cast aluminum intake manifold that offers advantages that only a modular design could allow. Using the latest in CFD (Computational Fluid Dynamics) software; Skunk2 Racing has created a two-piece modular design that allows for easy disassembly, porting, and plenum volume changes through the use of a removable plenum lid and optional plenum spacers. In addition to CFD testing, the Ultra Series Intake Manifold has undergone extensive in-house dyno testing which has led to a design that is less restrictive, yielding both torque and power gains well over many of the competitors.   Skunk2 Racing Ultra Street Intake Manifolds are cast-aluminum, manufactured from high-grade 356 aluminum alloy for strength and lightweight. Each manifold is CNC-machined for a precise fit, and individually inspected for quality assurance. The Ultra Series Street manifold features a generous 71mm throttle body opening and is constructed with thick walls at entry, minimizing concerns of breakthrough when port matching. Intense planning and design went into the plenum to distribute even airflow to all four cylinders under dynamic load conditions. Placement and design of the velocity stacks were rigorously flow tested to ensure maximum delivery of air to the cylinder. Large velocity stack raised bell mouth entries lead to 6.85” long intake runners with smooth transitions allowing the Ultra Street Intake Manifold to really move some air! Skunk2 Racing Ultra Street Intake Manifolds are designed to be used in modified naturally aspirated applications as well as mild turbo/supercharged setups.
Weight1215215
Dimensions1 × 1 × 1 in20 × 16 × 9 in18 × 6 × 6 inN/AN/A20 × 16 × 9 in
Additional information
Weight 12 lbs
Dimensions 1 × 1 × 1 in
Brand

Injector Dynamics

Weight 15 lbs
Dimensions 20 × 16 × 9 in
Brand

Skunk2

Weight 2 lbs
Dimensions 18 × 6 × 6 in
Brand

Skunk2

Brand

Skunk2

Brand

Skunk2

Weight 15 lbs
Dimensions 20 × 16 × 9 in
Brand

Skunk2

Select the fields to be shown. Others will be hidden. Drag and drop to rearrange the order.
  • Image
  • SKU
  • Rating
  • Price
  • Stock
  • Availability
  • Add to cart
  • Description
  • Content
  • Weight
  • Dimensions
  • Additional information
  • Attributes
  • Custom attributes
  • Custom fields
Click outside to hide the comparison bar
Compare
Compare ×
Let's Compare! Continue shopping
X