Accord 03-07| ID2600-XDS
$2,173.50 – $2,249.10
ID2600-XDS, for 03-07 Accord / J-series V6. 11mm (red) adapters. S2K lower. Set of 6.
- Nominal Flow Rate – 2600cc/min @ 3.0 Bar (43.5 psi)
- Maximum Differential Fuel Pressure – 9.0 Bar (130.5 psi) – Requires Minimum 11volt.
- Fuel Compatibility – Compatible with Methanol/Ethanol/All Known Hydrocarbons. NOT Compatible with Ethers (MTBE, ETBE, TAME) or Nitro Methane
- Electrical Connector – USCAR
The ID2600-XDS is the most recent offering from the partnership of Injector Dynamics and Bosch Motorsport.
The ID2600-XDS was developed specifically for use with liquid fuels, featuring corrosion resistant internals, and long term compatibility with ethanol and methanol.
The ID2600-XDS has the highest flow rate of any injector offered by Bosch, and flows 50% more than the ID1700x.
The ID2600-XDS benefits from Dual Slope Matching, a method of matching the flow rate in both the linear, and nonlinear operating range, providing better cylinder to cylinder consistency at low pulse widths.
|Dimensions||1 × 1 × 1 in|
|Settings||Accord 03-07| ID2600-XDS remove||Alpha 70mm Throttle Body - B/D/F/H Series remove||Pro Intake Manifold - EVO VIII-IX remove||Fuel Rail - Ultra Race - B Series Primary remove||Fuel Rail - Ultra Race - B Series Secondary remove||Ultra Street Intake Manifold - B VTEC - Black remove|
|Price||$2,173.50 – $2,249.10|
|Add to cart|
|Description||ID2600-XDS, for 03-07 Accord / J-series V6. 11mm (red) adapters. S2K lower. Set of 6.
FEATURES: Precision Die-Cast Aluminum Fine Shot-Blasted Surface Finish Precision Machined Brass Throttle Plate Compatible w/ OEM Throttle Cable Sealed Ball Bearings for Smooth Operation New Throttle Body Gasket and Hardware Idle Adjustment Screws for Fine Tuning
Match with a Skunk2 Pro Series Throttle Body for an easy 30+ hp gain.
-NPT threaded ports
- Hardware with plugs or barbed fittings for vacuum purposes
- Dipstick Relocator
||350-05-6000 Engineers at Skunk2 Racing have developed a Primary Fuel Rail for the popular Ultra Race Intake Manifold. FEATURES: Manufactured from Billet 6061 Aluminum Hard Anodized for Corrosion Resistance Large .669" Internal Bore -8 ORB Ports Supports Up to 1,200HP Compatible w/ E85 and Methanol. Requires Remote Mount Regulator.||350-05-6010 Engineers at Skunk2 Racing have developed a Secondary Fuel Rail for the popular Ultra Race Intake Manifold. FEATURES: Manufactured from Billet 6061 Aluminum Hard Anodized for Corrosion Resistance Large .669" Internal Bore -8 ORB Ports Supports Up to 1,200HP Compatible w/ E85 and Methanol. Requires Remote Mount Regulator.||307-05-0505
Modular 2pc. Design w/ Removable Plenum
Rotatable Plenum Allows Driver-side or Passenger-Side Throttle Body Mounting
1.8L Plenum Volume
Tapered 8.72" Long High-Velocity Runners w/ Raised Velocity Stack Entries
Generously Cast Runner Walls for
74mm Throttle Body Opening
Lightweight 356 Aluminum Alloy Construction
2 x 1/8" NPT and 2 x 1/4" NPT Accessory Ports
Hi-Grade Mounting Hardware
Thermal Gasket Included
|Content||The ID2600-XDS is the most recent offering from the partnership of Injector Dynamics and Bosch Motorsport. The ID2600-XDS was developed specifically for use with liquid fuels, featuring corrosion resistant internals, and long term compatibility with ethanol and methanol. The ID2600-XDS has the highest flow rate of any injector offered by Bosch, and flows 50% more than the ID1700x. The ID2600-XDS benefits from Dual Slope Matching, a method of matching the flow rate in both the linear, and nonlinear operating range, providing better cylinder to cylinder consistency at low pulse widths.||Skunk2 is proud to introduce the 70mm Alpha Series Throttle Body for Honda B16/ B17/ B18/ B20/ D15/ D16/ F20/ F22/ F23/ H22 and H23 engines in its exclusive, fine shot-blasted surface finish. Skunk2’s Alpha Series Throttle Body is designed to be used with Skunk2’s Pro Series Intake Manifolds as well as OEM and other aftermarket intake manifolds for bolt-on horsepower and torque gains by maximizing engine airflow, all at a competitive price.
A larger throttle body is key to producing additional power throughout the powerband on modified engines with increased airflow demands and the Skunk2’s 70mm Alpha Series Throttle Body delivers! Sealed ball bearings, a precision machined throttle plate and a honed oversized bore insures smooth operation on the most aggressive naturally aspirated and forced induction applications.
||The intake manifold solution street-driven Evo VIII-IX owners have been waiting for is here. Skunk2’s newly designed Evo Pro Series Intake Manifold was designed with “street enthusiasts” who utilize turbochargers as small as the factory unit in mind and want more power without sacrificing mid-range performance. Skunk2’s all-new, cast-aluminum Evo Pro Series Intake Manifold—which was tested and developed on the company’s own Evo Time Attack race car—is a direct-fit replacement and offers significant horsepower and torque gains without compromising mid-range power output. Conventional large-plenum, short-runner intake manifolds provide top-end power gains but suffer in the mid-range. Not Skunk2’s. Its all-new Pro Series Intake Manifold features OEM-length runners with larger bores and a special tapered design as well as a larger, tapered plenum that together preserve mid-range power but increase and accelerate airflow to allow for significant top-end gains. Peak gains as high as 33+ whp have been realized when paired with Pro Series Throttle Bodies with positive results across the board, beginning as low as 3,200 rpm. Pro Series Intake Manifolds also feature thicker castings when compared to the OEM piece, which leaves plenty of room for porting, and each runner exit is machined and hand-finished to best match the cylinder head’s ports. The Pro Series Intake Manifold’s unique design increases wave scavenging effects at the engine’s ideal operating range, which allow for a broad increase in usable power. Skunk2’s Evo Pro Series Intake Manifold is a simple bolt-on affair. Unlike other intake manifolds, Skunk2’s incorporates the factory configuration, leaving the throttle body in its original location, which means the original intercooler piping and hoses can be reused. Pro Series Intake Manifolds also include the necessary provisions for the Evo’s brake booster line, MDP sensor, and vacuum accessories (EGR valve excluded), and incorporate two additional 1/8-inch NPT threaded ports, which can be used for any number of vacuum/boost-related devices such as gauges, boost controllers, and more. Each manifold comes equipped with plugs and fittings as well as a dipstick k relocator. Skunk2 is a familiar name in the intake manifold business, with more than 10 years of experience designing, testing, and building them. Similar to OEM manifolds, Skunk2’s Pro Series Intake Manifolds are shell-molded from 356-aluminum, CNC-machined for superior strength, a precise fit, and a high-quality finish, and vacuum-tested for quality. Each manifold is molded with smooth transitions from the throttle body opening to the plenum to the runners with clean parting lines for an optimal finish, both inside and out and features a genuine Skunk2 nameplate.||Fitment:
||The much anticipated Ultra "Street" intake manifolds for the Honda B16A/ B17A and B18C engine or VTEC cylinder heads has finally arrived! The Ultra Series is years of research and development, culminated in a multi-piece cast aluminum intake manifold that offers advantages that only a modular design could allow. Using the latest in CFD (Computational Fluid Dynamics) software; Skunk2 Racing has created a two-piece modular design that allows for easy disassembly, porting, and plenum volume changes through the use of a removable plenum lid and optional plenum spacers. In addition to CFD testing, the Ultra Series Intake Manifold has undergone extensive in-house dyno testing which has led to a design that is less restrictive, yielding both torque and power gains well over many of the competitors. Skunk2 Racing Ultra Street Intake Manifolds are cast-aluminum, manufactured from high-grade 356 aluminum alloy for strength and lightweight. Each manifold is CNC-machined for a precise fit, and individually inspected for quality assurance. The Ultra Series Street manifold features a generous 74mm throttle body opening and is constructed with thick walls at entry, minimizing concerns of breakthrough when port matching. Intense planning and design went into the plenum to distribute even airflow to all four cylinders under dynamic load conditions. Placement and design of the velocity stacks were rigorously flow tested to ensure maximum delivery of air to the cylinder. Large velocity stack raised bell mouth entries lead to 8.72” long intake runners with smooth transitions allowing the Ultra Street Intake Manifold to really move some air! Skunk2 Racing Ultra Street Intake Manifolds are designed to be used in modified naturally aspirated applications as well as mild turbo/supercharged setups.|
|Dimensions||1 × 1 × 1 in||10 × 8 × 8 in||N/A||16 × 5 × 3 in||16 × 5 × 3 in||20 × 16 × 9 in|